WonderBart

Friday - Ready engine and mount up in engine bay Today I got the engine ready for mounting and decided to use my original D15B7 engine mount and bracket. The power steering bracket on the other hand is one that I got from the wrecker from a D16Z6 engine. Installing the engine back into the car took a lot of patience I had a friend of mine work the hoist while I moved the engine around and started bolting up the mounts. Before lowering the engine into the engine bay I attached the rear engine bracket to the engine, then got my friend to lower the engine into place while I worked the bolt to catch some thread. After that I worked the tranny mount and got a bolt thru that and finally had to use a floor jack to help align the drivers side mount and stuck a bolt thru that. Once the main mounts were done I installed the left and right torque mounts, power steering pump and some hoses. Tommorrow the plan is to finish her up and get her running. D16A chained up and ready installation D16A in the process of being installed D16A almost installed D16A ... Read More

Thursday - D16A Maintenance and external assembly So far out of the 4 days, today was the funnest till the end but I'll get into that later. Putting something together is always more fun because you start seeing a little glimps of your final product and you get more existed. Today I started by taking the JDM exhaust manifold off as it is different from mine so I can't use it. Then I mounted the flywheel and new clutch, and finally bolted up the transmission. I did some maintenance on the engine too and replaced the thermostat, PCV Valve and new oil filter. After that I mounted my old wire harness including fuel injectors with the fuel rail, alternator and starter. Most of the plugs were easy but one thing I noticed was that I did not have a Purge Valve on this engine so I will have to reuse my old one from my D15B7 and just add it to my vacuum lines. I cleaned off the old throttle body gasket from the intake and then bolted on the throttle body and and connected all the appropriate hoses. Toward the end of the day I started screwing back all the ... Read More

Wednesday - Old engine extraction and engine bay cleanup Today started early at 9am, I picked up my flywheel from the Lordco machine shop and pressure plate bolts and throttle body gaskets from Honda. The bonus for today was I had a friend help me out to extract the engine out with was a great benefit while using the host cuz 2 people are always better then one. Unbolting the mounts was pretty easy but finding a place to hook up the chain was a bit tricky but by lunch time the motor was out. Soon after I sprayed the Engine compartment down with Simple Green a biodegradeable degresser and then hosed it down a couple of times. I made sure my fuel lines with wrapped up and after I used compressed air to blow out any of the electrical plugs and around any place water shouldn't be. Engine being lifted out by hoist Almost high enough to be pulled out On the left is engine bay before cleaning and right is after cleaning Full shot of clean engine bay, and on the right is another shot of old greasy D15B7  For The Previous Step Click Here > D16A Engine Swap - Day 2 For ... Read More

Tuesday - Ready old engine for extraction First thing in the morning I dropped off the Flywheel for machining and headed to Princess Auto for some oil drain pans and some other items. To start the engine removal process I jacked up the car and put it on stands ready for drive shaft removal. Taking both the axle nuts off was actually pretty easy but when I got to the lower ball joints is when the trouble started. I worked on those for a couple of hours but had no success so I decided to do something different. I took the top of the suspension off including the struts and managed to get both the axles off. The drivers side CV boot was already cracked so grease was everywhere but I am glad it broke on my stock wheels and not my new mags. After that I drained the coolant from the engine and took the radiator out and started to work on the electrical plugs and hoses. I found out that to separate the main plugs on both the left and right side I had to take them off the mounting brackets. Toward the end of the night I managed ... Read More

Monday - Get parts and prep the new engine I started the day by calling around for parts, organizing my tools and figuring what I had to do first. Then I went to MOPAC and picked up a Centerforce Dual Friction Clutch and Coquitlam AutoParts for the water pump, timing belt and pilot bearing. By the time I got started it was already 3pm so there was no time to waste. While changing the water pump and timing belt I ran into a problem taking off the main crankshaft bolt even with my heavy duty impact wrench. So I sprayed the bolt with lube and went onto unbolting the transmission. Pulling the tranny was pretty easy with the engine out, so in no time at all I had the whole clutch assembly apart. I went back to the front of the engine and this time I heated up the crankshaft pulley bolt and managed to get it off. The rest of the water pump and timing belt was a snap just bolt everything back on. After that I noticed that the throttle plate was really dirty so I pulled the whole throttle body of the intake and cleaned it up with ... Read More

It's a great start to 2008 as I have acquired a JDM D16A VTEC Engine with only 80,000KM's. It came with an Si tranny, Distributor and the P28 ECU. The plan is to change the timming belt, water pump and to replace the stock clutch with a Center Force 2 Clutch, Bearing and Pressure plate to get a better grip on the newly added horsepower. With this new engine, Short Ram Intake and my 2.5" exhaust I should be putting out 135-140HP now so laying rubber should be easy to do, and maybe get 2nd gear chirps. I took a picture of the engine with my cell phone but the lighting wasn't the best so the picture is a bit grainy but here it is the D16A VTEC. As you'll notice the valve cover is silver but down the road I will pull it off and get it powder coated cherry apple red to match the car. ... Read More